AT91SAM7X256C-AU Microcontroladores ARM - MCU LQFP GRN IND TMP MRL C

 E kenyelletsa ARM7TDMI ARM Thumb® Processor

 Boqapi bo phahameng ba 32-bit RISC Architecture

 Sete ea Taelo ea 16-bit e phahameng haholo

 Moetapele ho MIP/Watt

 EmbeddedICE™ In-circuit Emulation, Debug Communication Channel Support

 Flash ea ka hare ea lebelo le phahameng

 512 Kbytes (SAM7X512) E Hlophisitsoe ka Libanka tse Peli tsa Maqephe a 1024 a 256 Byte (Dual Plane)

 256 Kbytes (SAM7X256) E hlophisitsoe ka Maqephe a 1024 a 256 Byte (Sefofane se le Mong)

 128 Kbytes (SAM7X128) E Hlophisitsoe ka Maqephe a 512 a 256 Byte (Sefofane se le Mong)

 Ho fihlella ha Mokoloko o le Mong ho fihla ho 30 MHz maemong a Mabe ka ho Fetisisa

 Prefetch Buffer E Ntlafatsa Phethahatso ea Taelo ea Monoana o Monoana ka Lebelo le Leholo

 Nako ea Lenaneo la Leqephe: 6 ms, Ho kenyeletsoa Leqephe la ho itlhakola, Nako ea ho Hlakola ka ho Feletseng: 15 ms

 10,000 Write Cycles, 10-year Retention Capability, Sector Lock Capabilities, Flash Security Bit

 Fast Flash Programming Interface bakeng sa Tlhahiso e Phahameng ea Molumo

 SRAM ea Lebelo le Phahameng ka Hare, Phihlello ea potoloho e le 'ngoe ka Lebelo le Leholo

 128 Kbytes (SAM7X512)

 64 Kbytes (SAM7X256)

 32 Kbytes (SAM7X128)

 Molaoli oa Memori (MC)

 Selaoli se Kenyellelitsoeng sa Flash, Boemo ba ho Amoha le ho Khetholla ho Fosahetseng

 Reset Controller (RSTC)

 E ipapisitse le Lisele tsa ho Seta Botjha ha Matla le Sebui sa Brownout se nang le matla a Tlase

 E fana ka Sebopeho sa Letšoao la Reset ea Kantle le ho Beakanya Botjha Boemo ba Mohloli

 Oache jenereithara (CKGR)

 Oscillator ea matla a tlase, 3 ho isa ho 20 MHz On-chip Oscillator le PLL e le 'ngoe

 Taolo ea Tsamaiso ea Matla (PMC)

 Bokhoni ba ho Matlafatsa Matla, ho kenyeletsoa Mokhoa o liehang oa Clock (Ho theohela ho 500 Hz) le Mokhoa o sa sebetseng

 Lipontšo tse 'nè tsa Clock tsa ka ntle tse lokiselitsoeng

 Advanced Interrupt Controller (AIC)

 Motho ka mong a ka Maskable, Boemo ba Bohlokoa ba Borobeli, Mehloli e Thibelang Likokoana-hloko

 Mehloli e 'meli ea Tšitiso ea Kantle le Mohloli o le Mong oa Khatiso o Potlakileng, Tšitiso e Senyehileng e Sirelelitsoeng

 Setsi sa Debug (DBGU)

 UART ea terata tse 2 le Tšehetso bakeng sa tšitiso ea Seteishene sa Puisano ea Debug, Thibelo ea Phihlello ea ICE

 Mokhoa oa Morero o Akaretsang 2-terata ea UART Serial Communication

 Nako ea Nako ea Nako (PIT)

 20-bit Programmable Counter hammoho le 12-bit Interval Counter

 Windowed Watchdog (WDT)

 12-bit key-protected Programmable Counter

 E fana ka Lipontšo tsa ho tsosolosa kapa ho sitisa Sisteme

 Counter e ka Emisoa Ha processor e ntse e le ho Debug State kapa Idle Mode

 Sebali sa Nako ea 'Nete (RTT)

 32-bit Free-rung Counter e nang le Alamo

 E Mathisela ka hare ho RC Oscillator

 Balaoli ba babeli ba Parallel Input/Output (PIO)

 Methati e Mashome a tšeletseng a metso e 'meli e Lokisehang ea I/O e Multiplexed ka li-Peripheral I/Os tse fihlang ho tse peli

 Matla a Kena a Phetoho Moleng o Mong le o mong oa I/O

 Ka Setho ka Setho se Bulehileng, se Hulelang-up le Sephetho sa Synchronous

 Mecha e Leshome le Metso e meraro ea Pheripheral DMA Controller (PDC).

 Lebelo le Le leng la USB 2.0 (12 Mbits ka motsotsoana) Port Device Port

 On-chip Transceiver, 1352-byte Configurable Integrated FIFOs

 One Ethernet MAC 10/100 base-T

 Media Independent Interface (MII) kapa Reduced Media Independent Interface (RMII)

 Li-FIFO tse kopaneng tsa 28-byte le likanale tsa DMA tse inehetseng bakeng sa ho fetisa le ho Amoheloa.

 Karolo e le 'ngoe ea 2.0A le Karolo ea 2.0B e Ikamahanyang le CAN Controller

 Mabokose a Melaetsa a Melaetsa a robeli a hlophisehang ka botlalo, Counter ea setempe sa nako ea 16-bit

 One Synchronous Serial Controller (SSC)

 Lits'oants'o tsa Oache e Ikemetseng le Frame Sync bakeng sa Moamoheli le Mofetisi e mong le e mong

 I²S Tšehetso ea Sebopeho sa Analog, Tšehetso ea Nako ea Multiplex ea Nako

 Bokhoni ba ho Phatlalatsa Boitsebiso bo Tsoelang Pele ka lebelo le phahameng le 32-bit Transfer ea data

 Li-transmitters tse peli tsa Universal Synchronous/Asynchronous Receiver (USART)

 Motho ka mong oa Baud Rate Jenereithara, IrDA® Infrared Modulation/Demodulation

 Tšehetso bakeng sa ISO7816 T0/T1 Smart Card, Hardware handshaking, RS485 Support

 Tšehetso e Feletseng ea Mohala oa Modem ho UART1

 Lisebelisoa tse peli tsa Master/Slave Serial Peripheral Interfaces (SPI)

 8- ho isa ho 16-bit Bolelele ba Boitsebiso bo Reroang, Likhetho tse 'nè tsa kantle tsa Peripheral Chip

 Mocha o le mong oa 16-bit Timer/Counter (TC)

 Lintho tse Tharo tsa Kantle tsa Oache, Lithakhisa tse peli tsa Multi-purpose I/O ka Channel ka ’ngoe

 Moloko o Habeli oa PWM, Mokhoa oa Capture/Waveform, Bokhoni ba Holimo/Down

 Taolo e le 'ngoe ea Mecha e mene ea 16-bit Power Width Modulation Controller (PWMC)

 One Two-wire Interface (TWI)

 Master Mode Support Feela, Li-EEPROM tsohle tsa terata tse peli tsa Atmel le lisebelisoa tse tsamaellanang tsa I2 C li tšehelitsoe

 Sefetoleli se le seng sa 8-bit 10-bit Analog-to-Digital, Mecha e Mene e Multiplexed ka Digital I/Os

 Thuso ea SAM-BA® Boots

 Lenaneo la kamehla la Boot

 Sehokelo se nang le SAM-BA Graphic User Interface

 IEEE® 1149.1 JTAG Boundary Scan on All Digital Pins

 Li-I/Os tse mamellang 5V, Ho kenyeletsoa le mela e mene ea I/O ea Drive ea Hona joale e Phahameng, Ho fihla ho 16 mA ka ngoe.

 Lisebelisoa tsa Motlakase  E Kenyellelitsoeng 1.8V Regulator, Ho Rala ho fihla ho 100 mA bakeng sa Likarolo tsa Koko le Kantle

 3.3V VDDIO I/O Lines Power Supply, Ikemetseng 3.3V VDDFLASH Flash Power Supply

 Phepelo ea Motlakase oa 1.8V VDDCORE e nang le Mohloli oa Brownout

 Tšebetso e tsitsitseng ka ho Fetisisa: Ho fihla ho 55 MHz ho 1.65V le 85°C Maemo a Mabe ka ho Fetisisa

 E fumaneha ka har'a liphutheloana tse tala tsa LQFP tse 100 le libolo tse 100 tsa TFBGA